Calculate the equivalent ducting allowances using: (__in.
equivalent length. 
R* Equivalent length of duct pieces is based on an actual test conducted by GE Evaluation Engineering and reflects requirements for good venting performance. This downdraft blower system is designed for use with 3-1/4 x 10 ductwork (can be transitioned to 6 round). Two different discharge directions are available with side to- side adjustment for the accurate alignment of ductwork. Before cutting out the countertop, refer to instructions packed with downdraft and cooktop. Please copy and paste this embed script to where you want to embed. We need your help to maintenance and improve this website. Comment document.getElementById("comment").setAttribute("id","a0c061c3b56f79d9f8ec4af6e70436b2");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. STEPS TO DETERMINE FLEXIBLE DUCTINGS EQUIVALENT LENGTH, 500 CFM Make sure everyone is focused only on your food with a 500-CFM venting system that removes smoke, grease, odors and moisture from the air.Adjustable fan speed Adjust your vents to match your cooking techniques with infinite fan control that removes grease, odors and moisture.Grease filters Keep your clean-up to a minimum with a removable grease filter that helps eliminate hand scrubbing.Aluminum mesh filters Easy to remove, dishwasher safe.Hides into countertop Raises over cooktop surface and retracts when not in use.Model UVD6361SPSS Stainless Steel, UVD6301DP Universal 30" Telescopic Downdraft System DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES) NOTE: Telescopic downdraft vents are not, GE Profile 36" Built-In Gas Cooktop Installation Guide FEATURES AND BENEFITS Start cooking faster with Power Boil Maximize, GE Appliances Dishwasher User Manual - Optimized PDF GE Appliances Dishwasher User Manual - Original PDF, GE Appliances Washer Instructions Manual - Optimized PDF GE Appliances Washer Instructions Manual - Original PDF. Against the wall, installations are limited to dimension requirements. 
Thank you for using our services. May 1, 2017 | Author: Earl Henderson | Category: N/A, Installation Instructions Classic Downdraft Vent Models: RV30, RV36, RV46 Includes installation instructions for optional cabinet blower (Dacor model CABP3).
NOTE: The countertop must be at least 26 deep with a flat surface area of 23-1/2 or more, front to back. In addition, other clearances to the front edge of the countertop must be considered. Please fill this form, we will try to respond as soon as possible. Check the location of floor joists, wall joists, wall studs, electrical wiring or plumbing for possible interference. 
Measure the actual amount of offset (Maximum 3 recommended). Your email address will not be published. Home GE APPLIANCESS GE APPLIANCESS Universal 36 Telescopic Downdraft System UVD6361SP User Guide, UVD6361SPUniversal 36 Telescopic Downdraft System. on GE APPLIANCESS Universal 36 Telescopic Downdraft System UVD6361SP User Guide, DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES), GE APPLIANCESS Vented Range Hoods Installation Guide, GE APPLIANCESS Universal 36" Telescopic Downdraft System UVD6361SP, GE APPLIANES UVD6301DP Universal 30" Telescopic Downdraft System Installation Guide, GE Profile 36" Built-In Gas Cooktop Installation Guide, Tech4home Lda MAIN S2 Remote Control User Manual, electro-harmonix 360538 BAD STONE Phase Shifter Pedal Instructions, ZERFUN G8 Pro Wireless Microphone System User Manual, Airrex Infrared Heater AH-200/300/800 User Manual, 2017 Toyota Camry Hybrid LE Fuse Box Diagrams, 2017 Mitsubishi Lancer 4WD Fuse Box Diagrams, Mitsubishi Lancer Passenger and Engine Fuse Box Diagram, Mira Honesty ERD Bar Valve and Fittings User Manual. Please help us to share our service with your friends. NOTE: Telescopic downdraft vents are not recommended to be installed with cooktops that are flush-mounted.Approved for use with the following Monogram, GE Profile Series and GE Series cooktops36 electric models, 36 gas-sealed burner models and 36 induction models.NOT APPROVED FOR USE WITH STANDARDBURNER GAS COOKTOPS. The effect upon airflow is dependent upon the amount of offset.
NOTE: Dimensions shown are for reference only. We are a non-profit group that run this service to share documents. Total equivalent length of ducting should not exceed the maximum recommendation of 100 feet for optional venting performance. For best performance: choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. offset) x (14 ft. per inch) =__ft. For answers to your Monogram, GE Caf , GE Profile , or GEAppliances product questions, visit our website at geappliances.com orcall GE Answer Center Service, 800.626.2000. To keep our site running, we need your help to cover our server cost (about $500/m), a small donation will help us a lot. Refer to installation instructions packed with the product for further details. NOTE: Installation on cabinets/countertops against the wall will not be possible in most applications.