Installed my windshield with it against installers advice and found out not only was he right but the windshield sat up to high for the trim to be installed. But this is one job for which I will dust off my box of disposables. Place the new glass/gasket assembly on a work surface and insert the rope into the U channel that wraps around the pinchweld. 
Arbomast Autograde) is designed to stay pliable, because of inherent body/glass movement, so it only surface skins. 
One way to do it. Getting ready to install my windshields and I went to a local paint shop to get some more tubes of the beutel sealant. I would also recommend smearing lubricant ( e,g, washing up liquid) all round the inner lip to help the pull and reduce pinching/ripping risk against the pinchweld. Lubricant and adhesive contacting the same bonding surface is a risky proposition, since the former will compromise the effectiveness of the latter. Pull the rope along the bottom and half way up the side on both sides of the glass assembly. Widely Application: Butyl sealant tape for all types of vehicles (cars, RVs, boats) and houses (windows, screen doors, skylights, vents),designed for waterproofing, shock absorption and noise isolation, perfect for taillights and headlights sealants.
Repeat the procedure with the other top chrome piece. Then take the lower half molding and slide the small corner flange into the gasket and join the bottom piece to the side piece already inserted. Sorry to be so abrupt, but that will produce nothing but problems. Headlight Sealant Easy To Use: Butyl sealant tape is chemically resistant and very flexible,it can be flattened or stretched as needed for easy installation.Please clean the installation area in advance before use. Particularly, in the case of an installation where it is impossible to seal the gasket after the glass and gasket have been roped in; how do you suggest one would properly negotiate around this dilemma, to preserve the integrity of the adhesive bond to the pinchweld?. 
B2-20120091-4. 1995-2021, Quadratec, Inc. All rights reserved. They didn't have it in the tubes, but had 15 feet of beutel rope in 1/4, 5/15, and 3/8 beads. Here is one of the tips I promised. Knowing this would be a mess either way, I went with the bead in the glass channel and another in the rope channel. Onetouch Lazada, Browse Alphabetically: 1967 - 1981 Firebird Windshield Glass Installation Seal Ribbon Rope Tape, Front or Rear, Each, Driven Racing Oil Lubricants and Additives, Miscellaneous Automatic Transmission Components, Miscellaneous Manual Transmission Components, 1970 - 1974 Rear Window Moldings Trim Set, BLACK ANODIZED, 1967 - 1969 Firebird Windshield Molding Clips, Lower, Corners, Front Upper and Sides for Coupe, 1967 - 1969 Firebird CLEAR CONVERTIBLE Front Windshield Glass, Without Tint Band, 1967 - 1969 Front Windshield Chrome Moldings Set - Hardtop Coupe, 1967 - 1969 Firebird Rear Window Chrome Molding Clips Set, 1967 - 1969 Firebird Rear Window Moldings Chrome Polished Stainless Set, Coupe. Pull both ends of the rope at the same time and pull the inner lip around the remaining pinchweld. For, DMT Windshield & rear window trim removal tool for all window that use clips to hold on the stai, DMT Windshield & rear window locking strip installation tool. For a better experience, please enable JavaScript in your browser before proceeding. Removed by cutting out new gasket with razorblade, cleaning channel and starting over. Then seal between the glass and gasket and you are done. Then lip the longer J flange into the gasket groove with the hook tool. Noticed the headliner was not in. It may be necessary to break the seal between the gasket lip and the vehicle body with a hook tool before applying interior pressure. Wouldnt it be easier add the sealant before you insert the glass into the gasket? Many others recommend a bead in the channel where the rope goes, etc. Intellectual Property Protection | Suppliers There are so many opinions on how to do this, the shop manual says to add a bead in the gasket where the glass goes and then add a bead around the body flange. How Auto Glass Contributes to Fuel Efficiency. Once the corner is free, simply push along the pinchweld and separate the assembly from the body. Rich is the only person I have ever seen use it on a seal like the Mustang has. Abrupt is right, nothing much is more annoying to go through all that work and then find your windshield leaks like a sieve. A forum community dedicated to vintage Ford Mustang owners and enthusiasts. - User Information Legal Enquiry Guide, 1999-2022 Alibaba.com. should the headliner be wrapped around the upper lip of the opening or should it stop at the opening if installing windshield with headliner? The most difficult of all is the old Ford windshield DW819 with chrome molding accents. Quadratec, Inc, has no affiliation with FCA. Tmall Taobao World Cool, I will go with the tubes. Use of washing up liquid as a lubricant has been used widely in the glass fitting business prior to polyurethane bonding, for indirect glazing. Repeat on the other corner. Now grasp one of the side rope ends and pull the rope always towards the center of the glass and knuckles on the glass. It only contacts the inner lip of the pinchweld. Lesson learned.
I highly recommend that if you can rope-in rather than lip-in, it would be to your best interest to do so. Also the vehicle Im doing has a very old and rusty pinchweld. And it's not often you go wrong following the shop manual. The glass/gasket assembly is removed by applying pressure to the inside of the glass while manipulating the interior lip of the gasket downward to force the assembly free. The pressure is usually started in one of the two upper corners. Butyl rubber is high viscosity, elasticity and tightness. This is the most difficult part of the job. The edge of the glass was protected by the gasket that was attached to the edge before the glass was placed into the opening. This is not the point of seal for the gasket. Good thinking from Merlin. . it wouldn't be the first time reality took theory and conjecture out behind the woodshed and gave them a good thrashing. The name rope-in comes from the tool you use to install the glass into the opening, a length of braided nylon rope that is 25 ft. long and usually - or -inch in diameter. The type of sealant recommended for this type if fitting ( e.g. And I'm sure he stands behind his work. Come join the discussion about restoration, modifications, NOS parts, troubleshooting, VIN codes, and more! I'm using the rubber gasket too, not going to put the rope down and then the glass without a gasket. document.getElementById( "ak_js_1" ).setAttribute( "value", ( new Date() ).getTime() ); This site uses Akismet to reduce spam. Those ropes are what GM used in the '60's and '70's to install glass. Your email address will not be published. Next week will be the lip-in installation method. Merlin, Just follow the Mustangs to Fear video. Using urethane with a rubber gasket is contradicted by, well, almost everybody. A plastic or nylon version of the knife would no doubt be better.
| Affiliate, Product Listing Policy Butyl Rubber Sealant: Rubber Sealant is a non-drying,non-hardening synthetic rubber based butyl rubber sealant. I will be installing windshield myself I hope this makes it easier for install. Use forscr, 2022 Detroit Muscle Technologies, LLC. I destroyed the gasket and have to get another one and give it another go. If it does not seat correctly, use a hook tool to lip the gasket over the pinchweld until the entire bottom is seated. Privacy Policy This walks the rope around the gasket corner and allows the assembly to fall into place. Should I have the owner clean the weld before I give it another go? Stop and seat the gasket over the pinchweld by using your fingertips. what do I need to pay attention to keep from pulling the headliner out? The assembly will then fall into the opening and the out lip will seal automatically. It sat on the pinch, and then the glass stuck to the butyl rope. DO NOT pull the rope outwards because it causes a scissor type action that will tear the gaskets inner lip. The rope will tear the tape while it is pulled and the excess tape can be easily pulled out. Alibaba.com Site: International - Espaol - Portugus - Deutsch - Franais - Italiano - - P - - - - - Trk - Nederlands - ting Vit - Indonesian - , AliExpress All Rights Reserved. I returned the rope and the place did have the bedding and glazing compound, just needed to talk to the right guy. Alipay Seems like the rope is the same stuff in the tubes, just a littler firmer so it would be a cleaner install. Probably hard to do as the rope would strip out the sealer.
- You will feel the gasket seat onto the pinchweld. Also in an ideal world the glass will slip into the aperture easily, but sometimes you need to slap it in to get achieve a good seating. Throughout this website and catalog the terms Jeep, Wrangler, MOPAR, & Rubicon are used for identification purposes only. Make your next windshield repair less of a struggle with the Precision Parts, Precision Replacement Parts Rope-In Windshield Gasket Tool, Overland Vehicle Systems Canyon Bag Rolled General Tool Tote w/ Handle, JKS Manufacturing JKS 3/8" Heavy Duty Shank Step Drill Bit, Be the first to ask a question about this item, ** Free Shipping Details, Shipping Policies and Restrictions. 1688.com I'm sure Rich wouldn't do it if it didn't work, and I bet he has installed a LOT more glass than I have. that 1% is his use of urethane. | I always wanted to install using the rope-in method over the lip-in because it was less likely that breakage would occur during installation. JavaScript is disabled. No reproduction without expressed written permission.Questions? Take the glass/gasket assembly and set it into the opening making sure that the excess rope ends are accessible from the inside of the vehicle. | 33010002000092 Apply a bead of sealant/adhesive on the gasket lip that contacts the body. Ergonomic Design : Angled tip to make cord installation simple the first time. When you get to the top corner use your outer hand finger tips to apply pressure and while pulling the rope twirl the rope in a small circular fashion.
| I gave it a good effort today put couldnt negotiate the square corners on the top with the rope. | Showroom Your email address will not be published. Butyl Sealing Rope Purpose: Butyl rubber 13Ft/4M suitable for sealing car doors,windshield,waterproof film,hood,lights,body plate joints and other parts of the shock seal. Now that we know the two types of gasket styles, lets address the first of three methods of installation, the rope-in method. | Country Search This will hold the chrome into the gasket while the assembly is roped into place. - It is easier and safer for the vehicle, glass and technician. I've never bothered with a rope and the last few years I've been installing mine with an old butter knife. Take the side molding J flange and slide it into the molding groove manufactured into the gasket and use the hook tool or pick to lip the remaining gasket groove over the molding flange. I'm just old school. Required fields are marked *. The glass/gasket assembly is usually easier to push out when the first corner is separated from the body. I usually start on the bottom center with about two to three feet of excess rope for pulling purposes. I agree with his install 99%. For use on ALL makes and models; A, DMT Firm plastic toolwith rounded, thin, blunt end and chiseled scraping end.
He installed backlite with no butyl but I am going to go around it with the glazing and push it in with a "popcicle stick". Knowing how, where and how much to slap is important. not no, but hell no! Once the glass/gasket assembly is out of the opening, separate the gasket from the broken glass and attach it directly to the new glass part. The correct stuff is "bedding and glazing compound" and that's it. There is plenty of enough durable rope to fit around even the, Good"how to use a rope tool" video linkhttps://www.youtube.com/watch?v=iIkggbLRQbg, DMT Windshield OR rear window seal chrome locking strip and stainless locking strip seam connector f, DMT Rear window cold knife removal tool for rear windows that use butyl caulk not rubber seals. "The important thing is not to stop questioning. Apply slight pressure on the outside surface of the glass assembly and grasp one of the rope ends and pull the rope upwards with your knuckles against the glass surface. There are six pieces to the chrome moldings; two on the top, two on the bottom, and one on each side. +1 on NO BUTYL!! Butyl Sealing Rope Multi-function: Headlight sealant retrofit anti-leakage, anti-corrosion, anti-deformation, anti-vibration, anti-aging, chemical corrosion resistance, very flexible, can be flattened or stretched, easy to install. I apply it before installing it because it is less of a mess. Learn how your comment data is processed. Then take one of the top halves and slide the larger portion of the J flange into the top gasket groove. Will that inhibit the gasket from slipping on nicely? Threaded Nylon Cord : 1/4" cording, wraps the largest truck windshields. Posted by :Bob Beranek On : January 3, 2013. Terms of Use Curiosity has its own reason for existing".Einstein, 1965 Ford Mustang fastback T5 Ncas 9in Locker. The passenger side gives you more room to maneuver so I usually start in the upper passenger side corner. How would I negotiate square corners? | DMT Use the rope in tool when working with rubber gasket set glass. - Jeep, Wrangler, Rubicon, Renegade, CJ, Quadra-Trac and the Jeep grille design are registered trademarks of FCA (Fiat Chrysler Automobiles). The lubricant is smeared on the inner lip of the gasket. I was doing it solo so figured if I put a bead on the body flange it would be all over by the time I got the windwo centered. Contact info@agrrmag.com. |, Windshield Seal & Rear Window Seal Installation Setting Rope Tool, https://www.youtube.com/watch?v=iIkggbLRQbg, Mopar A Body 63-66 Barracuda Dart Valiant Windshield OR Rear Window Gasket Seal Chrome Locking Strip Trim, Windshield Seal and Rear Window Seal Removal Knife Cutting Tool, Windshield Seal & Rear Window Seal Trim Removal Tool, Windshield Seal & Rear Window Seal Locking Strip Insertion Tool, Windshield Seal & Rear Window Seal Installation Plastic Tool Scraper. I found this video (has a part 2 also) that seems to cover all the necessary steps. 2022 AGRR Magazine. 1967 - 1981 Camaro Windshield Glass Installation Seal Ribbon Rope Tape, Front or Rear, Each, Driven Racing Oil Lubricants and Additives, Storage Protection, Additives, and Cleaners, Radiator Support, Header, & Valance Panels, Third Gen Used Original Ground Effects ( 82 - 92 ), Horn Buttons, Caps, Shrouds and Components, QA1 High Quality Performance Suspension Products, Miscellaneous Automatic Transmission Components, Miscellaneous Manual Transmission Components, 1967 - 1969 Rear Window Chrome Molding Clips Set, 1967 - 1969 Camaro Rear Window Moldings Chrome Polished Stainless Set, Coupe, 1967 - 1969 Camaro Tinted Coupe Windshield Glass with Upper Tint Band, 1967 - 1969 Windshield Molding Clips, Lower, Corners, Front Upper and Sides for Coupe, 1967 - 1969 Rear Back Window Glass, Coupe, Clear, 1970 - 1974 Rear Window Moldings Trim Set, BLACK ANODIZED, 1967 - 1969 Camaro CLEAR CONVERTIBLE Front Windshield Glass, Without Tint Band, 1967 - 1981 Molding Clip Installation Tool, 1967 - 1969 Camaro Windshield Chrome Moldings Set, Coupe.