The video also describes how to read the Omnimeter with a computer via direct connection, how to make meter settings, how to setup a wireless connection to read the meter remotely, and how to install the EKM Push (now Push3) gateway for cloud-based data. Use the barrel jack port or the +/- terminal block.
No. The email includes your EKM Push account key, which provides administrative access to your Push account and your meter data. Single phase 3-wire systems (some call them two phase or Edison) have 2 hot wires and a neutral wire. You can connect the EKM Push3 to your Wifi network, or you can connect an ethernet cable from you internet router to the ethernet port in your EKM Push. Modified on: Tue, 29 Mar, 2022 at 4:43 PM. After booting the Push3 will look for an available firmware update. The images and diagrams shown here are in no way exhaustive. If you purchase your Omnimeter(s) and EKM Push3 together then the Push3 should be plug-and-play when you receive your order. Assuming that your meters are installed correctly, and you have followed the appropriate instructions, your EKM Push3 should already be pushing data over the internet to our cloud database. The use and installation of 485Bees is explained in the video above. This could be a 480/277 volt system, or a 120/208 volt system. Here is another installation video from Appalachian DIY: Did you find it helpful? You will need 1 Omnimeter and on 3-phase 4-wire systems have 3 hot wires and a neutral wire. EKM Push3 installation from Appalachian DIY: Small 3mm standard screwdriver (included), Twisted pair wire for the RS-485 data connections (sold separately), Ethernet cable if not connecting to WiFi (sold separately). Push3 spec sheet and installation instructions, Did you find it helpful? These are generally older 3-phase systems. There are in fact many possible ways to install an Omnimeter. There are in fact many possible ways to install an Omnimeter. In this case the meter is an Omnimeter Pulse v.4 but installing a v.3 or v.5 Omnimeter is done in a very similar way. If you cannot hardware the Omnimeter to the Push3, then you can wirelessly bridge the RS-485 communication using 485Bee zigbee radio modules. Sorry we couldn't be helpful. Yes Installation instructions for use with the v.4/5 Omnimeter models: Booting the Push3 gateway takes ~4 minutes. Do not use both. Sorry we couldn't be helpful. If a new firmware version is available, the Push3 will download it and update automatically. Use the barrel jack port or the +/- terminal block. You can use your key to log in to your Push Account Portal here: https://api.ekmpush.com/account.html?key=*enter*key*here*. Only share this key with parties that you wish to provide this level of privileges. Twisted pair wire for the RS-485 data connections. Fuse Installation and Wiring the Breaker Panel, Installing the Meter and Current Transformers, Installing 485Bee Radios and the EKM Push Gateway. Connect the 12V DC power adapter from any 110-240V AC outlet to the appropriate port on your EKM Push3. Here is a video showing proper wiring of an Omnimeter I v.3 installed on a 120 volt electrical system: Here is a video showing proper wiringof an Omnim Single-Phase 2-wire 120 volt, 240 volt, 230 volt (non-U.S.) Metering, Single-Phase 3-Wire 120/240V or 120/208V Metering, Electricity and/or Water and/or Gas Metering. Modified on: Wed, 30 Mar, 2022 at 10:01 AM. No. Installation instructions for use with the EKM-Omnimeter II UL v.3: Use a small standard screwdriver to install one strand of twisted pair wire from terminal 20 (A) on your Omnimeter to the RS-485 (A) terminal block of the EKM Push3. Yes If you purchase your Omnimeter(s) and EKM Push3 together then the Push3 should be plug-and-play when you receive your order. Help us improve this article with your feedback. Installation instructions for use with the EKM-Omnimeter I v.3: Use a small standard screwdriver to install one strand of twisted pair wire from terminal 11 (A) on your Omnimeter to the RS-485 (A) terminal block of the EKM Push3. To learn how to access all of your meter data, please refer to the EKM Push account information email that we sent out when the system was purchased. This video provides one example of how to install an Omnimeter. Use a small standard screwdriver to install one strand of twisted pair wire from terminal 12 (B) on your Omnimeter to the RS-485 (B) terminal block of the EKM Push3. Situational variables will determine how your installation may differ but this video should at least provide some of the basic principles you should consider when installing your metering system. It will have been pre-assign We don't work closely with installers so we can't give you qualified recommendations of who should install our products. This is the most common residential syste 3-phase 3-wire systems have 3 hot wires and NO neutral wire. You can use the following links to jump to specific video parts: Part 3 - Testing, Pulling Wires, and Labeling, Part 4 - Fuse Installation and Wiring the Breaker Panel, Part 6 - Installing the Meter and Current Transformers, Part 9 - Installing 485Bee Radios and the EKM Push Gateway. This video provides one example of how to install an Omnimeter. If you had purchased your Omnimeters separately then you will need to contact EKM to have them assign the Omnimeter serial numbers to your Push3 gateway. It can take up to 30 minutes for the update to complete. Help us improve this article with your feedback. We also included a hard copy of that email with the first order.
Connect the 12V DC power adapter from any 110-240V AC outlet to the appropriate port on your EKM Push3. No additional hardware or software is necessary in order for your EKM Push to send your Omnimeter data to the cloud. It will have been pre-assigned to read the Omnimeters that you purchased. Use a small standard screwdriver to install one strand of twisted pair wire from terminal 21 (B) on your Omnimeter to the RS-485 (B) terminal block of the EKM Push3. The account portal allows you to see the status of all of your meters and gateways, as well as craft API queries and make meter settings.