If you have questions, contact the manufacturer at the. Any third-party replacement part used may cause serious damage and drastically reduce the performance level of your unit, which will result in premature failure. REPLACEMENT PARTS AND REPAIRSIn order to ensure your unit remains in good working condition, you must use Broan-NuTone LLC or Venmar Ventilation ULC genuine replacement parts only. You know you have a Class ABC extinguisher and you, B. NOTE:On 8-ft. ceilingsHood distance above the cooktop is Minimum 26, Maximum 34 (for ducted discharge)Minimum 26, Maximum 31 (for non-ducted discharge)On 9-ft. ceilingsHood distance above the cooktop is: Minimum 32, Maximum 36 (for both ducted andnon-ducted discharge)On 10-ft. ceilingsHood distance above the cooktop is a Minimum of 32, Maximum of 36 (for both ducted and non-ducted discharge).NOTE: 10-ft. ceilings require 10-ft. Flue Extension, Model FXN58SS for ducted or non-ducted installations (purchase separately). CAUTION: Use only flexible duct provided. Install (2) washers and (2) no. Press on the current blower speed another time to stop it.
This product may have sharp edges.
Install the lower flue bracket to the lower flue using (2) flue bracket screws (no. Aluminum Duct (not shown).
The bottom of the hood MUST NOT BE LESS than 26 and at a maximum of 36 above the cooktop for best capture of cookingimpurities. No Other Warranties: This Limited Warranty contains the Companys sole obligation and your sole remedy for defective products. Center the bracket over the hood location and flush with the ceiling. Any cleaners that contain bleach will attack stainless steel. 8 x 3/8 mounting screws. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Incidental damages include but are not limited to such damages as loss of time and loss of use. tj@E
Grease should not be, d) Use proper pan size.
stream << For ducted installation only:Install both damper flaps inside the blower exhaust opening, ensuring the pins are top-oriented. Slide up the upper flue upward until it is aligned with its upper flue mounting bracket. Two installers are recommended because of the size of, 8. Attach flexible duct to non-duct plenum collar and secure with a tie wrap. Turn the filter mounting tabs to remove the filter and replace it. off the power unit.
8 x 3/8 screws through the lower flue side slots. Crpes Suzette, Cherries Jubilee, Peppercorn Beef Flamb).c) Clean ventilating fans frequently. TO REDUCE THE RISK OF INJURY TO PERSON(S) IN THE, EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE, 1. The disclaimers, exclusions, and limitations of liability under this warranty will not apply to the extent prohibited by applicable law. Carefully replace the upper flue inside the lower flue. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside. To the extent that applicable law prohibits the exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition is limited to the period specified for the express warranty above. The bracket should be inside the flue. INSTALLER: LEAVE THIS GUIDE WITH THE HOMEOWNER. A sleek, low-profile design enhanced by a dazzling finish.
Ad' xV (1H[Tw Attach aluminum flexible duct to the damper/ductconnector with a tie wrap. /BitsPerSample 8 Ducted fans must always be vented to the outdoors. 23 0 obj When the service, disconnecting means cannot be locked, securely fasten a, prominent warning device, such as a tag, to the service, 3.
/Domain [0 1] Remove protective plastic film covering the flue and the hood.
8 x 3/8 screws through the lower flue side slots, Slide the upper flue upward until it is aligned with its upper flue mounting bracket. NEVER PICK UP A FLAMING PAN You may be burned. Insert the included drywall anchors into the drilled holes(one for each hole). This is your sole and exclusive remedy for breach of this limited warranty. Pull down the metal latch tab, push the filter into position, and release. Follow the heating equipment manufacturers guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. %
)JVG$Bm7'Vgz,[aO8%0K0cD6Q#C1L L=2mLU?E)1t}_VD80ds-+ujfDC0c=#UdI;Y1bgXe@wd#h;]o%sza4.Y$2$ajiKeUSVhxm[ >kfVr=x_wB^$5)xqOii IF THE FLAMES DO NOT GO OUT IMMEDIATELY. Grease filters are dishwasher safe.Clean all-metal filters in the dishwasher using a non-phosphate detergent. Unpack hood and check contents. Tighten the screws completely. Please read specification label on product for further, Manual will be automatically added to "My Manuals", Ventilation Hood Broan BW50 SERIES Instructions Manual, Ventilation Hood Broan BW5330SS Installation Use And Care Manual, Ventilation Hood Broan BWP1244SS Instructions Manual, Ventilation Hood Broan BW5830SS Installation Use And Care Manual, Ventilation Hood Broan BEST BER02IS Manual, Ventilation Hood Broan B3030SS Instructions Manual, Ventilation Hood Broan BC2130SS Installation Instructions Manual, Ventilation Hood Broan B5630SS Instruction Manual, Ventilation Hood Broan B5630SS Instructions Manual, Ventilation Hood Broan B5630SS Quick Start Manual, Ventilation Hood Broan B5330SS Installation Instructions Manual, Ventilation Hood Broan BDF SERIES Installation Manual, Ventilation Hood Broan BDF Series Installation Instructions Manual, Page 6: Install Upper Flue Mounting Bracket. 8 x 3/8 mounting screws. Install wall cap or roof cap. The minimum hood distance above the cooktop MUST NOT BE LESS than 26.A maximum of 36 above the cooktop is highly recommended for the best capture of cooking impurities.Distances over 36 are at the installer and users discretion; providing that the ceiling height permits. Tape all joints with duct tape. Home Broan BROAN BWP1244SS Chimney Range Hood Instructions, To register this product visit:www.broan-nutone.com orwww.broan.ca. Be careful to avoid cuts and abrasions during installation or cleaning. Long duct runs, elbows, and transitions will reduce the performance of the hood. xS TWI2o 1VI5YU{(**?IT 1)XbZFG:[T+Uqc{3gw{{/M4MiYd (9LRGzvMqUciUV5x+}u}?y:0a4gB8jG-Nb2L*t{=^=QTR"vD7D%:|;J=Ewt8H@NqEK.tDB]^1eEEBGfirBOV7zevgv=&w:Kn$zW;`ziYa#I;TPT5zLS*APIsXj2BMfRT&el*I7S:ohFhji-7umL6S$1N_|v[Mu@Z ZBk[x62pa!l6!d Hm8l]tg]ED!+}lJE>)%e-dy]*bnR1" `c Cewr_Qlo You may also use a specialized household stainless steel cleaner. 8 x 1 mounting screws.
/Length 2205 Any assistance the Company provides to or procures for you outside the terms, limitations, or exclusions of this limited warranty will not constitute a waiver of such terms, limitations, or exclusions, nor will such assistance extend or revive the warranty. This product may have sharp edges. Align the hood and center it above the hood mounting bracket. electrical wiring and other hidden utilities. * Included with optional Non-Duct Kit Model ARKBWP.Order service parts by Part No. Make sure that the bracket is positioned inside of the lower flue flanges with the slots on top. Replacement parts can be ordered on our website: www.broan.comfor US customers only. This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer purchaser.
Make sure that the slots of the upper flue bracket are at the bottom. Verify that the hood is centered and leveled. Attach non-duct plenum with collar to upper flue using (4) no. Slightly push aside the upper flue to avoid any damage while installing the lower flue to the hood top using (2) no. Always use cookware appropriate for. This warranty covers only replacement or repair of defective Products or parts thereof at the Companys main facility and does not include the cost of field service travel and living expenses. 
/Length 396
Be the first to learn about our special offers and sales. endstream /Range [0 1 0 1 0 1 0 1] When the 5-minute delay is activated, changing the blower speed will cancel the 5-minute delay function. Flue extension for higher ceilings is also available (sold separately), This hood can be installed non-ducted with the use of the accessory Non-Duct Kit (model number HRKMBLS sold separately). 6. 8. Use duct tape to make all joints secure and air-tight. Measure and install 6 round steel ductwork to roof cap or wall cap and 90 elbow over the blower exhaust opening on top of the hood. Do not exhaust air into spaces within. The fire is small and contained in the area where it. * Based on "Kitchen Fire Safety Tips" published by NFPA. Measuredistance A.This will be the length of the extended flex duct. /Decode [0 1 0 1 0 1 0 1] Larger ducting may be required for best performance with longer duct runs.
Slightly push aside the upper flue to avoid any damage while installing the lower flue to the hood top using (2) no. HOMEOWNER: OPERATION AND MAINTENANCE INFORMATION ON PAGE 2. Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or repair or replace, without charge, any Product or part thereof, to the extent the Company finds it to be covered by and in breach of this limited warranty under normal use and service. Broan-NuTone LLC and Venmar Ventilation ULC recommend contacting a certified service depot for all replacement parts and repairs.
A. If the motor continues to shut off and restart, have the hood serviced. You are responsible for all costs for removal, reinstallation and shipping, insurance or other freight charges incurred in the shipment of the Product or part to the Company. 8 x 3/8 mounting screws. e6)EIgf"{lf||U7$8GzR'F5'_)F]TH_rGetd|lF hV23dp",5g;p~Y7U?K When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities. bB _+-Sh{p4n -pDm/h+eE+- VK0! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S) OBSERVE THE FOLLOWING: TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:a) Never leave surface units unattended at high settings. The companyreserves the right, in its sole discretion, to refund the money actually paid by you for the Product in lieu of repair or replacement. See illustration below. Mounting height may be affected by ceiling height, Ducted telescopic flue accommodates ceiling heights from 8' to 9'. 7 $_mbynic @ B8`p#-kWWd0[jY`w+/M*BSc9*ZAk@SzbRxJ3p/;rC$x'J]Q. endobj Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be used close to a range. Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid under applicable law, but if any provision is held to be prohibited or invalid, such provision shall be ineffective only to the extent of such prohibition or invalidity, without invalidating the remainder of such provision or the other remaining provisions of the Limited Warranty. Exclusion of Damages: THE COMPANYS OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR, REPLACE OR REFUND, AT THE COMPANYS OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY AND THE COMPANYS SOLE AND EXCLUSIVE OBLIGATION. Always use cookware appropriate for the size of the surface element. unbalanced impeller, keep drywall spray, construction dust, 4. cooking flaming foods (i.e.
/Size [255] 2. Before servicing or cleaning the unit, switch power off at the service panel and lock service disconnecting means to prevent power from being switched on accidentally. hazardous or explosive materials and vapors. When cutting or drilling into wall or ceiling, do not damage. Expand. 8 x 3/8 Pan Head)7 Mounting Screws (no. cuts and abrasions during installation or cleaning. 2. How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and part identification and (c) describe the nature of any defect in the Product or part. Remove the grease filters by pulling down the metal latch tab and tilting filters downward to remove. If a framing member is not present, drill two 5/16 diameter holes where shown.
Align the hood and center it above the hood mounting bracket. Do not remove the protective plastic film covering the decorative flue and the hood at this time. Use a warm dishwashing detergent solution. Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if the Product does not work properly. >> The hood is operated using the push buttons on the front panel. Secure the upper flue to the upper flue mounting bracket using (2) no. Insert drywall anchors into the holes. 8 x 1 mounting screws through the hood back and into the drywall anchors. Be careful when installing the decorative flue and hood, 10. Install (2) washers and (2) no. The grease filters should be cleaned frequently. Secure the upper flue to the upper flue mounting bracket using (2) no. automatically shut off the motor if it becomes overheated. 
The bottom of the hood MUST NOT BE LESS than 24" and, at a maximum of 36" above cooktop for best capture of, 7. Always clean in the direction of original polish lines. With the hood hanging in place, drill through both holes located in the inside lower back of the hood using a 5/16 drill bit. Tilt the filter downward and remove it. Use as few of them as possible. Remove the upper flue from inside the lower flue.
Attach (2) two non-duct recirculation filters to the sides of the blower by aligning the key lock slot and rotating until filters lock into place. To avoid motor bearing damage and noisy and/or unbalanced impeller, keep drywall spray, construction dust, etc. Remove protective plastic film covering the lower flue only. Create a signature look and focal point in any personalized kitchen with this stunning black stainless chimney hood. Ducted fans must always be vented to the outdoors.
on BROAN BWP1244SS Chimney Range Hood Instructions, BROAN 353 Gable-Mount Powered Attic Ventilator Instruction Manual, BROAN BCDJ1 Undercabinet Range Hood Instruction Manual, Klarstein Athena 90 Range Hood User Manual, ancona Wall and Under Cabinet Range Hood User Manual, beyma Full Range Frequency Transducer User Manual, MONSTER MW215001 Smart Sports Watch Instruction Manual, SAINTWAY HC21SV 21.5 inch Full HD LCD POC Terminal with Bluetooth Instruction Manual, adastra MG220 Megaphone with Siren 30W User Manual, nacon PLANTRO-RIG800HS RIG 800 PRO HX Wireless Headphones User Guide, ZERFUN G8 Pro Wireless Microphone System User Manual, Airrex Infrared Heater AH-200/300/800 User Manual, 2017 Toyota Camry Hybrid LE Fuse Box Diagrams, 2017 Mitsubishi Lancer 4WD Fuse Box Diagrams, Mitsubishi Lancer Passenger and Engine Fuse Box Diagram, Mira Honesty ERD Bar Valve and Fittings User Manual, MOUNTING BRACKET LOCATION ABOVE 36 HIGH COOKTOP, Non-Duct Recirculation Filters (pair)(not shown) *, 6 Dia. The motor will restart when it cools down. This warranty covers only Products sold to original consumers in the United States and Canada by the Company or its U.S. and Canadian distributors authorized by the Company. Broan-NuTone LLC 926 West State Street, Hartford, WI 53027 www.broan-nutone.com 800-637-1453 Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville, Qubec, Canada J2C 7W9 www.broan.ca 1-877-896-1119, Klarstein Athena 90 Range Hood User Manual - Original PDF, ancona Wall and Under Cabinet Range Hood User Manual - Download [optimized] ancona Wall and Under Cabinet Range, beyma Full Range Frequency Transducer User Manual KEY FEATURES 3 full-range compact ferrite loudspeaker 60 W program power, SUMMIT 20" wide gas range 42" x 19.5" x 23.5" (H x W x D) 20" wide gas. At the time of requesting warranty service, you must present evidence of the original purchase date. Discoloration of the filters may occur if using phosphate detergents, or as a result of local water conditions but this will not affect filter performance. >> DO NOT REMOVE the protective plastic film covering the decorative flue and the hood at this time. This warranty also does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any Products or parts which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance, storage or repair (other than repair by the Company), (d) damage caused by faulty installation, or installation or use contrary to recommendations or instructions, (e) any Product that has been moved from its original point of installation, (f) damage caused by environmental or natural elements, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential use, or (j) damage caused by fire, flood or other act of God or (k) Products with altered, defaced or removed serial numbers. Carefully place both flues into the recessed area of the hood top.
Comment document.getElementById("comment").setAttribute("id","abe93bbbc7013c18a84053857fa829fa");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product, except for those incurred with the Companys prior written permission.
Use a piece of cardboard to avoid damaging the table or the hood. Carefully place both flues into the recessed area of the hood top. BTU/hr. D. You can fight the fire with your back to an exit. Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly. 6. Broan-NuTone LLC or Venmar Ventilation ULC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety. Use this unit only in the manner intended by the manufacturer. %0cZu-k%,80P!'?3U'"S|Aa
BURNS. MOTORThe motor is permanently lubricated and never needs oiling. INSTALLER: LEAVE THIS GUIDE WITH THE HOMEOWNER. Do not use this unit with any other solid-state speed control. NON-DUCTED RECIRCULATION FILTERSThe non-ducted recirculation filters should be changed every 6 months. THE COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES AND CONDITIONS, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES AND CONDITIONS IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. INSTALL THE HOOD (Horizontally Ducted Hoods Only), INSTALL THE HOOD (Vertically Ducted Hoods Only), (Non-Ducted Hoods Only)NON-DUCT KIT MODEL ARKBWP CONTENTS. Connect round metal ductwork to cap and work back towards the hood location. The electronic filter clean reminder ensures they will always maintain peak efficiency, Install hood so that the bottom of the unit is 24" to 30" above the cooking surface. << Tighten the screws completely. Lay the backside of the hood flat on a table.
If the motor bearings make an excessive or unusual noise, replace the blower with the exact service blower. Use any steel or stainless steel wool or any other scrapers to remove stubborn dirt. not by Key No.
i%^zZrw.x9#DL:3d0r%^0vsjJC M=p*]w5$Z-`+5#3jv y@%h`JPtS_XcGVBa BiVf#hmmcH~7z C]R0J (R=aTP7L6 4q8Z\%f ^nCoZjI'$fEld SMOTHER FLAMES with a close-fitting lid, cookie sheet, or, metal tray, then turn off the burner. Installation work and electrical wiring must be done by, qualified personnel in accordance with all applicable codes, and standards, including fire-rated construction codes and, 4. 8 x 1 mounting screws. 405/8 = bottom of hood 30 above the cooktop. Use duct tape to make all joints secure and air-tight. For screen reader problems with this website, please call859-342-60608 5 9 3 4 2 6 0 6 0Standard carrier rates apply to texts. 'XYJ4]Ljwd 5/J6gLab^Oy??vu9bHW=21y8)]uv)x&XDE$,gY;c. 8 x 3/8 pan head screws. Push the blower controls to select low, medium, or high blower speed (for each speed selected, it indicates light will beam).
If you cannot provide a copy of the original written limited warranty, then the terms of the Companys most current written limited warranty for your particular product will control. Wipe dry completely. Please read the specification label on the product for further information and requirements. A straight, short duct run will allow the hood to perform most efficiently. /Encode [0 254] ignite. Such Products and parts will be comparable in function and performance to an original product or part and warranted for the remainder of the original warranty period (or such longer period as may be required by applicable law). Tighten all screws completely. Broan Elite EW54000 Series 36" Chimney Range Hood-Black Stainless Steel with 500 cfm and 2 halogen lighting, Broan Elite EW54000 Series 36" Chimney Range Hood-Black Stainless Steel, Proposition 65 Warning for California Residents, Powerful 500 CFM internal blower operates at 1.5 sones at normal speed.
Before servicing or cleaning unit, switch power off at service, panel and lock service disconnecting means to prevent, power from being switch on accidentally.
Your email address will not be published. THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL, OR SPECIAL DAMAGESARISING OUT OF OR IN CONNECTION WITH THE PRODUCT, ITS USE, OR PERFORMANCE. INJURY TO PERSON(S) OBSERVE THE FOLLOWING: 1. Two installers are recommended because of the size of this hood. /Filter /FlateDecode TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR.