Tab will move on to the next part of the site rather than go through menu items. (a) When a check valve is used, a 3/16 (4.7 mm) air bleed hole must be drilled in the PVC pipe above the pump. The most common causes are a power outage by the electric company or a tripped circuit breaker. Products not received by GLENTRONICS, INC. at the address indicated below within thirty (30) days of the products defective performance will not be considered for warranty service. If any term is held to be illegal or unenforceable, the legality or enforceability of the remaining terms shall not be affected or impaired. MAKE SURE the supply circuit has a fuse or circuit breaker rated to handle the power requirements of this system. Install a gate valve or ball valve if required by any codes. This manual contains important SAFETY WARNINGS and OPERATING INSTRUCTIONS for the PHCC Pro Series 2400 battery backup sump pump system. . Be sure the area around the battery is wellventilated. The LED on the front of controller will signal the unit is receiving power. Plug the float switch cord into a properly grounded 3-prong receptacle. 1-1/2 rigid PVC pipe to connect to the existing plumbing, A check valve or union PVC pipe cleaner and cement. This manual should be retained for future reference. Connect the pipe on the pump to the existing discharge pipe with a rubber union or check valve and tighten the hose clamps securely. This will allow the pump to be removed easily, should the need arise. This pump is wired with a 3-prong grounded plug. . The electrical outlet should be within the length of the pumps power cord, and at least 4 feet above the floor. ALWAYS unplug the main pump when installing or servicing the backup pump or float switch to avoid electric shock. Now prime and cement a small piece of 1 PVC pipe to the bottom of a Y connector. Either the float is stuck in the up position, there is a mechanical problem with the pump, or there is a problem with the plumbing connections. . Pump or float problemThis key feature monitors the time that the float switch is up continuously or in the activated position. Install a check valve on the top of the pipe and tighten the bottom hose clamp. May result in death, serious injury, shock or burns. The circuit breaker to that outlet has been tripped, The ground fault interrupter on that outlet has been tripped, The power is out and the Power Failure Alarm slide switch is in the OFF position, The power is out and the 9V battery is discharged, The controller is not functioning. Drill the hole at a 45 angle toward the bottom of the sump to avoid splashing water outside the sump pit. Pmg Qrd _grhgs _ukp Qukp _ystgk hloju`gs9, nfttgry cjuh` jgvgj sglsdr, nfttgry ofnjgs, f 7, Pmg hltgrlfj odlstruothdl dc sdkg wgt ogjj nfttgrhgs, Ejgltrdlhos ofl ldt eufrfltgg tmg odkpfthnhjhty dc, fl` twd (>) omgob vfjvgs, `gpgl`hle dl tmg, F sgt dc nfttgry ofnjgs whtm rhles dl ndtm, gl`s td odllgot tmg twd nfttgrhgs tdegtmgr, Cjdft swhtom fssgknjy w/mdsg ojfkp . Do not overtighten the hose clamp. This check valve is mandatory when sharing a discharge line with another pump (i.e. What is Covered by this Warranty?GLENTRONICS, INC. warrants to the end purchaser that its pumps, switch and control unit products are free from defective materials and workmanship for the periods indicated below:All parts and labor (excluding installation) for a period of: What is NOT Covered by this Warranty?This warranty does not cover the cost or value of damaged property, including expressly any property that has been affected by water overflow, seepage or flooding. If you have a 2-prong receptacle, have a licensed electrician replace it with a 3-prong receptacle according to local codes and ordinances. If battery acid contacts skin or clothing, wash immediately with soap and water. DO NOT disassemble this product.
This will allow the pump to be removed easily, should the need arise. ALWAYS keep these instructions with the unit so that they will be easily accessible. You will need to refer to it before attempting any installation or maintenance. Do not remove or alter their position as it will disrupt the timing of the controller and how long the pump runs. Charge in a well-ventilated area. The pipe section exiting the building should be on a downward slope so that the water in the pipe will exit outside instead of returning to the sump pit. High water alarm (optional feature*)When water reaches the optional water sensor, it will activate the warning light, audible alarm, and remote terminal. (Requires purchase of PS-WiFi or PS-HZM) The Deluxe Controller is equipped with a USB data port. . Check the polarity of the battery posts. If the float switch does not move freely the pump will not activate. The Deluxe Controller features a series of warnings (audible and visual) that pinpoint potential problems with the pump, switch and power conditions. NEVER smoke or allow a spark or flame in the vicinity of the battery. .
. .independent, can be set at any level. If the product has been damaged, contact your place of purchase or Glentronics, Inc. before installation. .can run dry for short periods of time; can be used in sumps with water softener Float switch . Note: The 9V battery will only power the controller, not the pump. Dual Float ControllerThe Dual Float Controller will activate the pump when either float is lifted, and then shuts off automatically 10 seconds after the float drops. Make sure pump turns on at the intended level. Hold the float switch to the discharge pipe so the cage is below the bracket. pipe in the installation (including vertical and horizontal runs), install a check valve in place of the union. It might spark or short-circuit the battery and cause an explosion. Keep vent caps tight and level. (a) When using the vertical float switch with either the Enhanced or Deluxe Controller (Models VSC1.5 or VSC2), there are two rubber stoppers on the float switch rod.
It is included to indicate that the system is monitoring the sump conditions. This manual contains important SAFETY WARNINGS and OPERATING INSTRUCTIONS for the PHCC Pro Series 2400 battery backup sump pump system. AC power is outThere are several causes for power failure. Water will lift the bottom float by a 14, which will activate the pump. The same two options apply in very narrow sump pits where the backup pump must be mounted above the main pump. When used with the Deluxe Controller, the dual float switch has a safety locking pin. Replace it with a new 9-volt alkaline battery. . Reverse or replace the check valve. . .1014001 Battery box . Tighten nut on top of float, then replace c-clip on bottom of float.) MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. The pumps strainer must be kept clear. If battery acid contacts skin or clothing, wash immediately with soap and water. . Make sure it is installed with the arrow pointing up or it will not prevent the backflow of water. Comment document.getElementById("comment").setAttribute("id","a8d34d676ca1b095c67e554bbecff894");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. . GLENTRONICS, INC. disclaims all statutory and implied warranties, including without limitation, warranties of merchantability and fitness for a particular purpose and warranties against hidden or latent defects, to the extent permitted by law. With the risk of property damage from high water levels, the addition of a Pro Series battery backup sump pump system is highly recommended. Connect either wire to the common terminal.
A pit cover is recommended for all installations as a safety measure and to help prevent debris from falling into the pit. The dial can be adjusted from 5-45 seconds. DO NOT expose the control unit to any type of moisture, water, rain or snow. SAVE THESE INSTRUCTIONS. *Consult a licensed electrician. .non-corrosive, will not rust Pump . By using this method, there will always be an outlet for the water from the sump. This is a reminder to reset the alarm. Now prime and cement a small piece of 1 PVC pipe to the bottom of a Y connector. When AC power is restored, slide this switch back to the ON position. . .1113003 Battery filler bottle . Be sure the area around the battery is wellventilated. .
The Deluxe Controller includes a terminal on the right side of the control box to connect to a security system or other alarm devices.
To reduce the risk of electric shock, be certain that it is only connected to a properly grounded, 3-prong receptacle. DO. DO NOT use an attachment not recommended or sold by the manufacturer. If your pump is trying to discharge water into a full sewer, there is nowhere for the water to go. Do not use an extension cord. Once the float switch is in the desired position, tighten the clamp. Using sound plumbing practices, route the discharge pipe to an exterior wall via the shortest path with the fewest turns. This test will exercise the pump and help ensure the pump is working properly. .
Remove all debris from the float switch and float switch cage. This will allow the homeowner to address the problem.If this warning light and alarm are on, the control box is not receiving AC power for one of many reasons: Power Failure Alarm slide switchWhen the controller is not receiving AC power, the monitoring features and the audible alarms are powered by the 9-volt battery. The timer can be adjusted from 5-45 seconds. .1020011 Fluid sensor assembly .
. DO NOT use an extension cord. DO NOT use an extension cord. . . . . . Use the Pro Series control unit for charging a LEAD-ACID battery only. The controller will sound an alarm when power has been interrupted, when the pump has run for more than 10 minutes continuously, or when the 9V battery is low. Check valve on secondary pump will not close and. Depending on your installation requirements, PVC pipe lengths will vary. Enter and space open menus and escape closes them as well. A brick may be placed under the pump if there are rocks or other debris on the sump floor that may clog the pump. ohrouht nrgfbgr rftg` td mfl`jg tmg pdwgr, Umgl sgrvhog hs rgquhrg`, odltfot Ejgltrdlhos, ^gturl tmg odltrdj ulht td tmg kflucfoturgr cdr, dr ojdsg glduem td odkg td ydur fh` wmgl ydu, ofsg nfttgry foh` odltfots sbhl, ojdtmhle dr, rullhle odj` wftgr cdr ft jgfst 67 khlutgs, Gxpjdshvg efsgs oduj` ofusg sgrhdus hliury dr. ofusg nfttgry td gxpjd`g hl glojdsg` spfogs.
The Pro Series Connect Modules are separately sold accessories that will allow the user to stay connected and receive remote notifications of potential problems and needed maintenance while away from home. This water sensor is only designed to give you a warning of a potential problem; it will not activate the primary pump. As the pump evacuates the water from the pit the float will fall and the pump will run for an additional ten seconds to empty the pit. Tether Float Switch with Enhanced or Deluxe ControllersThe tether float contains a single float connected to a flexible tether. As the pump evacuates the water from the pit the float will drop, lowering the lift rod and turning off the pump.Note: The vertical float switch must be moving freely at all times. .
To reduce this risk, observe the following precautions. from interfering with the movement of the floats. The maximum amperage for the primary controller is 12 Amps. . In most cases, the backup pump will fit next to the main AC pump in the sump pit. (See page 18 for more information. Use the Pro Series control unit for charging a. Risk of electrical and fire hazard. Be sure protect the cords from damage when installing a pit cover. COMBINATION PRIMARY AC AND BACKUP SUMP PUMPS. . Do not use your product until you have read the terms of the warranty. The pump will run for an additional 10 seconds to extend the cycle after the lower float drops. A product shall be considered installed incorrectly when it deviates in any way from theinstructions described in this manual.
Bissell 1986 Series Revolution Pet Pro User Guide - Download [optimized]Bissell 1986 Series Revolution Pet Pro User Guide, Midiplus X pro mini Series MIDI Keyboard User Manual [X4 pro mini, X6 pro mini] - Optimized PDF, Eemax Pro Series XTP Tankless Electric Water Heaters User Manual - Download [optimized] Eemax Pro Series XTP Tankless, GET BLENDING DISCOVER MORE AT KITCHENAID.COM/QUICKSTART For exciting recipes, demo videos, product registration, and more, our quick start. Visually inspect your pump. More detailed instructions follow. Then, plug the pump into the receptacle on the float switch cord. Contact the Glentronics service department. Place the hose clamp over the discharge pipe so that the gripping tabs are against the pipe and select the desired activation level of the pump. If there is no check valve on the discharge pipe of the main AC pump, one must be installed at this time. The pit cover either has a hole punch that will allow the cord to be passed through or one can be drilled in the cover. Make sure it is above the water line and below the check valve. Check to ensure the float switch is connected to the controller. a back-up pump or a second primary pump). To extend the battery run time, two batteries may, The internal construction of some wet cell batteries, be connected to the Pro Series 2400 system by, The PHCC Pro Series 2400 A/C-D/C backup sump, purchasing a second battery and acid pack, as, Glentronics can not guarantee the compatibility of, other brands of batteries. If GLENTRONICS, INC. determines that a product is deemed defective under this warranty agreement, it will repair or replace the PRODUCT ONLY. If the security system requires an opening of a contact, secure the wire into the terminal hole labeled N.C. (normally closed). Avoid kinking the cord. . By discharging directly outdoors, there is always an outlet for the water that is pumped out of the sump. Two (2) acid packs to fill the dry batteries, A set of battery cables with rings on both ends to connect the two batteries together (available from Glentronics, Inc.), Use of a Pro Series Klunkless Check Valve will provide quieter operation. Mount the controller to the wall through the 2 holes on the cabinet using the proper mounting hardware for the application. . .
Check to ensure the float switch is connected to the controller. When installing or replacing a primary sump pump you should also install a battery backup sump pump system. Clear debris from inside the float cage (Loosen nut on top of float, then remove c-clip on bottom of float. Place the pump with the PVC pipe attachment on the bottom of the sump floor next to the main AC pump. To avoid debris from pouring onto the float, it should be positioned on the side of the discharge pipe opposite the drain tile. CAUTION: To reduce the risk of hazards that can cause injury or property damage, observe the following precautions. Mounting it above the drain tile would allow water to fill the drain tile before the pump is activated to pump out the water. The controller will also run the pump once a week for approximately four (4) seconds. Return the control unit to the manufacturer for any repairs at the following address: Sulfuric acid can cause blindness or severe burns. Make sure there is enough room so the backup pump and the main pump do not touch each other. Keep the cords separated from each other on opposite sides of the pipe. (Follow the instructions on the PVC cleaner and cement.). Then, plug the pump into the receptacle on the control box.
If the alarm continues to sound, replace the battery. The system is operatingThis light should be ON and flashing at all times. Do not cement them together until you are sure they are cut to the correct lengths. The use of a Pro Series, cables specifically designed for this use are, system to support your main AC sump pump, and. Connecting the Pump and Float Switch (Models VS and TS No Controller). odltrdj ulht cdr omfrehle `ry-ogjj nfttgrhgs, td njdw fwfy fly my`rdegl dr dxyegl efs tmft, khemt spfrb dr smdrt-ohrouht tmg nfttgry fl`, nrfogjgts, wftomgs, gto. (b) When using the vertical float switch without a controller (Model VS), the pumping range can be adjusted by moving the float stop up or down the lift rod. As the pump evacuates the water from the pit the floats will drop. the pump to any existing pipes; it should be placed on the floor of the sump. DO NOT operate this product if it has been damaged in any way. certain that it is only connected to a properly grounded 3-prong receptacle. The 9V battery (sold separately) runs the controller during a power outage, allowing it to sound an alarm if the circuit breaker trips, the controller is not plugged in securely, or the homes power is interrupted. The dual float switch contains two large floating rings enclosed within a protective cage. float switch is activated by rising water. Open the plastic door on the top of the Deluxe Controller and using a flat head screwdriver adjust the dial to select the number of seconds that the pump will run after the float drops.
Mount the controller to the wall through the 2 holes on the cabinet using proper mounting hardware for the application. Install a check valve on the top of the pipe and tighten the bottom hose clamp. . Dual Float ControllerPlug the control box into a properly grounded, 3-prong receptacle, then insert the pump plug into the receptacle on the control box. If you are installing it in the sump pit, it must to be installed between the basement floor and the primary float switch. . Cut the discharge pipe approximately one (1) foot above the floor. Remove the old pump and unscrew the pipe and adapter. (If the existing system is installed without a check valve or rubber union, saw the pipe apart above the sump pit.). 2022 Pro Series Pumps.
To reduce the risk of electrical shock, be. . Water will lift the float by a 12, which will activate the pump. When a check valve is used, a 1/8 hole must be drilled in the PVC pipe above the Pro Series pump. The illustration at right is an example of a typical battery backup installation. Do not mount. MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. Secure the float to the pipe with the enclosed hose clamp and bracket. Xdu whjj lgg` td rgcgr td ht ngcdrg fttgkpthle fly, hlstruothdls whtm tmg ulht sd tmft tmgy whjj ng, Cfhjurg td rgf` fl` cdjjdw tmgsg wfrlhles fl`. 1.Cut a piece of 1 rigid PVC pipe long enough to reach from the bottom of the sump pit to one (1) foot above the floor. Prior to defective operation, the unit must not have been previously altered, repaired or serviced by anyone other than GLENTRONICS, INC., or its agent; the serial number on the unit must not have been altered or removed; the unit must not have been subject to accident, misuse, abuse or operated contrary to the instructions contained in the accompanying manual. If the direct discharge method is not possible or convenient, the Pro Series pump can be connected to the same line as your main AC sump pump by installing a Y connector and two (2) check valves. Some states (countries and provinces) do not allow limitations on how long an implied warranty (or condition) may last, so the limitation described above may not apply to you. ALWAYS disconnect the pump and float switch controller from the power source before servicing or making adjustments. Prime and cement the top of the Y assembly to the discharge pipe with the Y extension facing down toward the backup pump. . The pump should not be set directly onto a clay, earthen, or sand base. DO NOT drop a metal tool onto the battery. This warranty does not cover product problems resulting from handling liquids hotter than 104 degrees Fahrenheit, handling inflammable liquids, solvents, strong chemicals or severe abrasive solutions; user abuse; misuse, neglect, improper maintenance, commercial or industrial use; improper connection or installation, damages caused by lightning strikes; excessive surges in AC line voltage; water damage to the controller; other acts of nature, or failure to operate in accordance with the enclosed written instructions.
. Water SensorThe water sensor is designed to warn you of a potential flood. Turn the screw a few turns to lock-in the wire. Loosen the check valve or rubber union by unscrewing the bottom hose clamp. Lower the pump into the sump by the handle. When reassembling the float, the magnetic strip on the inside of the float should be facing down. Be sure to seal the hole in the wall where the pipe exits, and prime and cement or clamp all connections securely to prevent leaking. NEVER handle the pump or motor with wet hands or when standing on a wet or damp surface while the pump is plugged into the power source. The float switch connector has asafety locking pin. . All Rights Reserved. If the above solutions do not solve the problem, contact Glentronics customer service 800-991-0466. DO NOT use in pits handling raw sewage, salt water or other hazardous materials. . Cut the pipes and assemble them as shown in photo #7.
Should any malfunction or emergency. For protection during a power outage, a Pro Series battery backup system should be installed. .
The manufacturer default is about 10 seconds. The 9-volt battery located in the top of the control box is coming to the end of its useful life. Do notremove or alter their position as it will disrupt the timing of the controller and how long the pump runs. The vertical float switch contains a single large float. Thoroughly read the instructions provided to learn specific details regarding installation and use. . . Drill the hole at a 45 angle toward the bottom of the sump to avoid splashing water outside the sump pit.
DO NOT use sump pumps in pits handling raw sewage, salt water, or hazardous liquids. 
It is important to read this manual, even if you did not install the Pro Series backup sump pump system, since this manual contains safety information regarding the use and maintenance of this product. . Failure to do this will prevent water from exiting the pit and damage the pump if the line freezes. Secure the float to the pipe with the enclosed hose clamp, but do not completely tighten the clamp at this time. Use a pit that conforms to all local codes and is large enough to accommodate the pump and float switch. The POSITIVE (+) battery post usually has a larger diameter than the NEGATIVE, When connecting the battery cables, first connect the small ring on the end of the WHITE wire to the NEGATIVE, Two (2) acid packs to fill the dry batteries, A set of battery cables with rings on both ends to connect the two batteries together (available from Glentronics, Inc.). Upload manuals that we do not have and get. Any and all causes of action arising from, filed as a result of or in reference to, this warranty or the products described under this warranty shall be governed by and construed under the laws of the State of Illinois. . To secure the wire into the terminal, insert the exposed wire into the hole on the side of the terminal next to the screw marked common. . . 4 years from the date of installation when purchased and installed by a contractor and when used intermittently as a sump pump, otherwise 3 years The defective product must be returned directly to the factory, postage prepaid with the original bill of sale or receipt to the address listed below. Locate the desired activation point.
CONNECTION TO AN EXISTING DISCHARGE PIPE (Diagram B). . The float switch wire of the Enhanced Controller includes a connector that can be separated from the controller when the wire needs to be threaded through small openings. In instances where the discharge line is exposed to freezing temperatures, the pipe must be sloped downward so any remaining water will drain out. . An in-line check valve is recommended to prevent back-flow. The float switch wire can now be disconnected. KEEP OUT OF REACH OF CHILDREN. Wash hands after handling. . This type of battery will power the controller for many hours, but not indefinitely. _mduj` fly kfjculothdl dr gkgregloy, dr tmg FO pdwgr, tmg Qrd _grhgs systgk whjj sdul`, odltrdj ulht whjj hl`hoftg tmg ofusg dc tmg, Cdr f``g` rgjhfnhjhty, tmg cjdft swhtom mfs, ldt, dlg, nut twd cjdfts kdultg` whtmhl f prdtgothvg, prdtgothvg ofeg prgvglts `gnrhs dr dtmgr whrgs. The product must be returned to GLENTRONICS, INC. for inspection in order to be considered for warranty service. . To avoid debris pouring into the float, it should be positioned on the side of the discharge pipe opposite the drain tile. DO protect the electrical cord from sharp objects, hot surfaces, oil and chemicals. In the event of an accident, flush with water and call a physician immediately. 6.Place the pump with the PVC pipe attachment on the bottom of the sump floor next to the main AC pump. As the pump evacuates the water from the pit the float will fall and turn off the pump. . A light on the display panel of the, control unit will indicate the cause of the alarm, A Pro Series 2200 Standby Battery or a Pro, DO NOT use an automotive battery with this, one, but two floats mounted within a protective, cage. any latin characters (a-z, A-Z) any numbers (0-9) special characters ("-", "_" and "."). DO NOT pull the cord when disconnecting the control unit. . If the security system requires a closing of a contact to activate the alarm, secure the other wire into the terminal hole labeled N.O. If the float switch does not move freely the pump will not activate. If the battery is good, the light will go out. Although the deluxe controller can not run the pump, it will sound an alarm indicating the loss of power. . This pump is wired with a 3-prong grounded plug. ALWAYS remove the power cord from the electrical outlet before connecting or disconnecting the battery cables. The dealers dated bill of sale, or installers invoice must be retained as evidence of the date of purchase and to establish warranty eligibility. If you do not agree to the terms of the warranty, do not use the product and return it within the return period stated on your purchase receipt from the retail store or authorized distributor where you purchased it for a refund. If there is a failure with either the main pump or the plumbing system, the water level will rise past the primary float switch and activate the water sensor. To reduce the risk of electrical shock, be, Someone should be within range of your voice or close enough to come to your aid when you work near a. . Make sure it is installed with the arrow pointing up or it will not prevent the backflow of water. When a check valve is used, a 1/8 hole must be drilled in the PVC pipe above the Pro Series pump. 3.When a check valve is used, a 1/8 hole must be drilled in the PVC pipe above the Pro Series pump. . f rhsb dc chrg dr hliury crdk fl gjgotrhofj smdob. To help reduce these risks, observe the following precautions: DO NOT walk on wet areas of the basement until all power has been turned off. After the initial installation, be sure to check the pump operation by filling the sump with water and observing the pump through several full cycles. 2.Secure the pump wire so that the plug on the end will not fall into the sump. DO NOT place the controller on the floor. Secure the pump wire so that the plug on the end will not fall into the sump. When connecting the battery cables, first connect the small ring on the end of the WHITE wire to the NEGATIVE (-) post of the battery, and then connect the large ring on the end of the BLACK wire to the POSITIVE (+) post of the battery. Enter your email address and check your inbox. . To the extent permitted by law, this warranty and the remedies set forth are exclusive and in lieu of all other warranties, remedies and conditions, whether oral, written, statutory,express or implied. The electrical outlet should be within the length of the pumps power cord, and at least 4 feet above the floor level to minimize potential hazards from flood conditions. 4.If there is no check valve on the discharge pipe of the main AC pump, one must be installed at this time. 0% found this document useful, Mark this document as useful, 0% found this document not useful, Mark this document as not useful, Save 278_2_Pro+Series+PHCC-2400+Manual For Later, systgk hlstfjjg` ny sdkgdlg gjsg, ydu kust rgf` fl` cdjjdw tmg. This pin will prevent the float switch from accidently being disconnected from the controller. This pin will prevent the float switch from accidentally being disconnected from the controller. This will preserve the battery and silence the alarm. . The controller should be mounted at least 4 from the floor and 1 from the outlet. . DO NOT use the control unit for charging dry-cell batteries that are most commonly used with home appliances.
Note: It is important to mount the float so that the activation level is below the drain tile that empties into the pit.
This will allow the pump to be removed easily, should the need arise. ALWAYS keep these instructions with the unit so that they will be easily accessible. You will need to refer to it before attempting any installation or maintenance. Do not remove or alter their position as it will disrupt the timing of the controller and how long the pump runs. Charge in a well-ventilated area. The pipe section exiting the building should be on a downward slope so that the water in the pipe will exit outside instead of returning to the sump pit. High water alarm (optional feature*)When water reaches the optional water sensor, it will activate the warning light, audible alarm, and remote terminal. (Requires purchase of PS-WiFi or PS-HZM) The Deluxe Controller is equipped with a USB data port. . Check the polarity of the battery posts. If the float switch does not move freely the pump will not activate. The Deluxe Controller features a series of warnings (audible and visual) that pinpoint potential problems with the pump, switch and power conditions. NEVER smoke or allow a spark or flame in the vicinity of the battery. .
. .independent, can be set at any level. If the product has been damaged, contact your place of purchase or Glentronics, Inc. before installation. .can run dry for short periods of time; can be used in sumps with water softener Float switch . Note: The 9V battery will only power the controller, not the pump. Dual Float ControllerThe Dual Float Controller will activate the pump when either float is lifted, and then shuts off automatically 10 seconds after the float drops. Make sure pump turns on at the intended level. Hold the float switch to the discharge pipe so the cage is below the bracket. pipe in the installation (including vertical and horizontal runs), install a check valve in place of the union. It might spark or short-circuit the battery and cause an explosion. Keep vent caps tight and level. (a) When using the vertical float switch with either the Enhanced or Deluxe Controller (Models VSC1.5 or VSC2), there are two rubber stoppers on the float switch rod.
It is included to indicate that the system is monitoring the sump conditions. This manual contains important SAFETY WARNINGS and OPERATING INSTRUCTIONS for the PHCC Pro Series 2400 battery backup sump pump system. AC power is outThere are several causes for power failure. Water will lift the bottom float by a 14, which will activate the pump. The same two options apply in very narrow sump pits where the backup pump must be mounted above the main pump. When used with the Deluxe Controller, the dual float switch has a safety locking pin. Replace it with a new 9-volt alkaline battery. . Reverse or replace the check valve. . .1014001 Battery box . Tighten nut on top of float, then replace c-clip on bottom of float.) MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. The pumps strainer must be kept clear. If battery acid contacts skin or clothing, wash immediately with soap and water. . Make sure it is installed with the arrow pointing up or it will not prevent the backflow of water. Comment document.getElementById("comment").setAttribute("id","a8d34d676ca1b095c67e554bbecff894");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. . GLENTRONICS, INC. disclaims all statutory and implied warranties, including without limitation, warranties of merchantability and fitness for a particular purpose and warranties against hidden or latent defects, to the extent permitted by law. With the risk of property damage from high water levels, the addition of a Pro Series battery backup sump pump system is highly recommended. Connect either wire to the common terminal.
A pit cover is recommended for all installations as a safety measure and to help prevent debris from falling into the pit. The dial can be adjusted from 5-45 seconds. DO NOT expose the control unit to any type of moisture, water, rain or snow. SAVE THESE INSTRUCTIONS. *Consult a licensed electrician. .non-corrosive, will not rust Pump . By using this method, there will always be an outlet for the water from the sump. This is a reminder to reset the alarm. Now prime and cement a small piece of 1 PVC pipe to the bottom of a Y connector. When AC power is restored, slide this switch back to the ON position. . .1113003 Battery filler bottle . Be sure the area around the battery is wellventilated. .
The Deluxe Controller includes a terminal on the right side of the control box to connect to a security system or other alarm devices.
To reduce the risk of electric shock, be certain that it is only connected to a properly grounded, 3-prong receptacle. DO. DO NOT use an attachment not recommended or sold by the manufacturer. If your pump is trying to discharge water into a full sewer, there is nowhere for the water to go. Do not use an extension cord. Once the float switch is in the desired position, tighten the clamp. Using sound plumbing practices, route the discharge pipe to an exterior wall via the shortest path with the fewest turns. This test will exercise the pump and help ensure the pump is working properly. .
Remove all debris from the float switch and float switch cage. This will allow the homeowner to address the problem.If this warning light and alarm are on, the control box is not receiving AC power for one of many reasons: Power Failure Alarm slide switchWhen the controller is not receiving AC power, the monitoring features and the audible alarms are powered by the 9-volt battery. The timer can be adjusted from 5-45 seconds. .1020011 Fluid sensor assembly .
. DO NOT use an extension cord. DO NOT use an extension cord. . . . . . Use the Pro Series control unit for charging a LEAD-ACID battery only. The controller will sound an alarm when power has been interrupted, when the pump has run for more than 10 minutes continuously, or when the 9V battery is low. Check valve on secondary pump will not close and. Depending on your installation requirements, PVC pipe lengths will vary. Enter and space open menus and escape closes them as well. A brick may be placed under the pump if there are rocks or other debris on the sump floor that may clog the pump. ohrouht nrgfbgr rftg` td mfl`jg tmg pdwgr, Umgl sgrvhog hs rgquhrg`, odltfot Ejgltrdlhos, ^gturl tmg odltrdj ulht td tmg kflucfoturgr cdr, dr ojdsg glduem td odkg td ydur fh` wmgl ydu, ofsg nfttgry foh` odltfots sbhl, ojdtmhle dr, rullhle odj` wftgr cdr ft jgfst 67 khlutgs, Gxpjdshvg efsgs oduj` ofusg sgrhdus hliury dr. ofusg nfttgry td gxpjd`g hl glojdsg` spfogs.
The Pro Series Connect Modules are separately sold accessories that will allow the user to stay connected and receive remote notifications of potential problems and needed maintenance while away from home. This water sensor is only designed to give you a warning of a potential problem; it will not activate the primary pump. As the pump evacuates the water from the pit the float will fall and the pump will run for an additional ten seconds to empty the pit. Tether Float Switch with Enhanced or Deluxe ControllersThe tether float contains a single float connected to a flexible tether. As the pump evacuates the water from the pit the float will drop, lowering the lift rod and turning off the pump.Note: The vertical float switch must be moving freely at all times. .
To reduce this risk, observe the following precautions. from interfering with the movement of the floats. The maximum amperage for the primary controller is 12 Amps. . In most cases, the backup pump will fit next to the main AC pump in the sump pit. (See page 18 for more information. Use the Pro Series control unit for charging a. Risk of electrical and fire hazard. Be sure protect the cords from damage when installing a pit cover. COMBINATION PRIMARY AC AND BACKUP SUMP PUMPS. . Do not use your product until you have read the terms of the warranty. The pump will run for an additional 10 seconds to extend the cycle after the lower float drops. A product shall be considered installed incorrectly when it deviates in any way from theinstructions described in this manual.
Bissell 1986 Series Revolution Pet Pro User Guide - Download [optimized]Bissell 1986 Series Revolution Pet Pro User Guide, Midiplus X pro mini Series MIDI Keyboard User Manual [X4 pro mini, X6 pro mini] - Optimized PDF, Eemax Pro Series XTP Tankless Electric Water Heaters User Manual - Download [optimized] Eemax Pro Series XTP Tankless, GET BLENDING DISCOVER MORE AT KITCHENAID.COM/QUICKSTART For exciting recipes, demo videos, product registration, and more, our quick start. Visually inspect your pump. More detailed instructions follow. Then, plug the pump into the receptacle on the float switch cord. Contact the Glentronics service department. Place the hose clamp over the discharge pipe so that the gripping tabs are against the pipe and select the desired activation level of the pump. If there is no check valve on the discharge pipe of the main AC pump, one must be installed at this time. The pit cover either has a hole punch that will allow the cord to be passed through or one can be drilled in the cover. Make sure it is above the water line and below the check valve. Check to ensure the float switch is connected to the controller. a back-up pump or a second primary pump). To extend the battery run time, two batteries may, The internal construction of some wet cell batteries, be connected to the Pro Series 2400 system by, The PHCC Pro Series 2400 A/C-D/C backup sump, purchasing a second battery and acid pack, as, Glentronics can not guarantee the compatibility of, other brands of batteries. If GLENTRONICS, INC. determines that a product is deemed defective under this warranty agreement, it will repair or replace the PRODUCT ONLY. If the security system requires an opening of a contact, secure the wire into the terminal hole labeled N.C. (normally closed). Avoid kinking the cord. . By discharging directly outdoors, there is always an outlet for the water that is pumped out of the sump. Two (2) acid packs to fill the dry batteries, A set of battery cables with rings on both ends to connect the two batteries together (available from Glentronics, Inc.), Use of a Pro Series Klunkless Check Valve will provide quieter operation. Mount the controller to the wall through the 2 holes on the cabinet using the proper mounting hardware for the application. . .
Check to ensure the float switch is connected to the controller. When installing or replacing a primary sump pump you should also install a battery backup sump pump system. Clear debris from inside the float cage (Loosen nut on top of float, then remove c-clip on bottom of float. Place the pump with the PVC pipe attachment on the bottom of the sump floor next to the main AC pump. To avoid debris from pouring onto the float, it should be positioned on the side of the discharge pipe opposite the drain tile. CAUTION: To reduce the risk of hazards that can cause injury or property damage, observe the following precautions. Mounting it above the drain tile would allow water to fill the drain tile before the pump is activated to pump out the water. The controller will also run the pump once a week for approximately four (4) seconds. Return the control unit to the manufacturer for any repairs at the following address: Sulfuric acid can cause blindness or severe burns. Make sure there is enough room so the backup pump and the main pump do not touch each other. Keep the cords separated from each other on opposite sides of the pipe. (Follow the instructions on the PVC cleaner and cement.). Then, plug the pump into the receptacle on the control box.
If the alarm continues to sound, replace the battery. The system is operatingThis light should be ON and flashing at all times. Do not cement them together until you are sure they are cut to the correct lengths. The use of a Pro Series, cables specifically designed for this use are, system to support your main AC sump pump, and. Connecting the Pump and Float Switch (Models VS and TS No Controller). odltrdj ulht cdr omfrehle `ry-ogjj nfttgrhgs, td njdw fwfy fly my`rdegl dr dxyegl efs tmft, khemt spfrb dr smdrt-ohrouht tmg nfttgry fl`, nrfogjgts, wftomgs, gto. (b) When using the vertical float switch without a controller (Model VS), the pumping range can be adjusted by moving the float stop up or down the lift rod. As the pump evacuates the water from the pit the floats will drop. the pump to any existing pipes; it should be placed on the floor of the sump. DO NOT operate this product if it has been damaged in any way. certain that it is only connected to a properly grounded 3-prong receptacle. The 9V battery (sold separately) runs the controller during a power outage, allowing it to sound an alarm if the circuit breaker trips, the controller is not plugged in securely, or the homes power is interrupted. The dual float switch contains two large floating rings enclosed within a protective cage. float switch is activated by rising water. Open the plastic door on the top of the Deluxe Controller and using a flat head screwdriver adjust the dial to select the number of seconds that the pump will run after the float drops.
Mount the controller to the wall through the 2 holes on the cabinet using proper mounting hardware for the application. Install a check valve on the top of the pipe and tighten the bottom hose clamp. . Dual Float ControllerPlug the control box into a properly grounded, 3-prong receptacle, then insert the pump plug into the receptacle on the control box. If you are installing it in the sump pit, it must to be installed between the basement floor and the primary float switch. . Cut the discharge pipe approximately one (1) foot above the floor. Remove the old pump and unscrew the pipe and adapter. (If the existing system is installed without a check valve or rubber union, saw the pipe apart above the sump pit.). 2022 Pro Series Pumps.
To reduce the risk of electrical shock, be. . Water will lift the float by a 12, which will activate the pump. When a check valve is used, a 1/8 hole must be drilled in the PVC pipe above the Pro Series pump. The illustration at right is an example of a typical battery backup installation. Do not mount. MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. Secure the float to the pipe with the enclosed hose clamp and bracket. Xdu whjj lgg` td rgcgr td ht ngcdrg fttgkpthle fly, hlstruothdls whtm tmg ulht sd tmft tmgy whjj ng, Cfhjurg td rgf` fl` cdjjdw tmgsg wfrlhles fl`. 1.Cut a piece of 1 rigid PVC pipe long enough to reach from the bottom of the sump pit to one (1) foot above the floor. Prior to defective operation, the unit must not have been previously altered, repaired or serviced by anyone other than GLENTRONICS, INC., or its agent; the serial number on the unit must not have been altered or removed; the unit must not have been subject to accident, misuse, abuse or operated contrary to the instructions contained in the accompanying manual. If the direct discharge method is not possible or convenient, the Pro Series pump can be connected to the same line as your main AC sump pump by installing a Y connector and two (2) check valves. Some states (countries and provinces) do not allow limitations on how long an implied warranty (or condition) may last, so the limitation described above may not apply to you. ALWAYS disconnect the pump and float switch controller from the power source before servicing or making adjustments. Prime and cement the top of the Y assembly to the discharge pipe with the Y extension facing down toward the backup pump. . The pump should not be set directly onto a clay, earthen, or sand base. DO NOT drop a metal tool onto the battery. This warranty does not cover product problems resulting from handling liquids hotter than 104 degrees Fahrenheit, handling inflammable liquids, solvents, strong chemicals or severe abrasive solutions; user abuse; misuse, neglect, improper maintenance, commercial or industrial use; improper connection or installation, damages caused by lightning strikes; excessive surges in AC line voltage; water damage to the controller; other acts of nature, or failure to operate in accordance with the enclosed written instructions.
. Water SensorThe water sensor is designed to warn you of a potential flood. Turn the screw a few turns to lock-in the wire. Loosen the check valve or rubber union by unscrewing the bottom hose clamp. Lower the pump into the sump by the handle. When reassembling the float, the magnetic strip on the inside of the float should be facing down. Be sure to seal the hole in the wall where the pipe exits, and prime and cement or clamp all connections securely to prevent leaking. NEVER handle the pump or motor with wet hands or when standing on a wet or damp surface while the pump is plugged into the power source. The float switch connector has asafety locking pin. . All Rights Reserved. If the above solutions do not solve the problem, contact Glentronics customer service 800-991-0466. DO NOT use in pits handling raw sewage, salt water or other hazardous materials. . Cut the pipes and assemble them as shown in photo #7.
Should any malfunction or emergency. For protection during a power outage, a Pro Series battery backup system should be installed. .
The manufacturer default is about 10 seconds. The 9-volt battery located in the top of the control box is coming to the end of its useful life. Do notremove or alter their position as it will disrupt the timing of the controller and how long the pump runs. The vertical float switch contains a single large float. Thoroughly read the instructions provided to learn specific details regarding installation and use. . . Drill the hole at a 45 angle toward the bottom of the sump to avoid splashing water outside the sump pit.
DO NOT use sump pumps in pits handling raw sewage, salt water, or hazardous liquids. It is important to read this manual, even if you did not install the Pro Series backup sump pump system, since this manual contains safety information regarding the use and maintenance of this product. . Failure to do this will prevent water from exiting the pit and damage the pump if the line freezes. Secure the float to the pipe with the enclosed hose clamp, but do not completely tighten the clamp at this time. Use a pit that conforms to all local codes and is large enough to accommodate the pump and float switch. The POSITIVE (+) battery post usually has a larger diameter than the NEGATIVE, When connecting the battery cables, first connect the small ring on the end of the WHITE wire to the NEGATIVE, Two (2) acid packs to fill the dry batteries, A set of battery cables with rings on both ends to connect the two batteries together (available from Glentronics, Inc.). Upload manuals that we do not have and get. Any and all causes of action arising from, filed as a result of or in reference to, this warranty or the products described under this warranty shall be governed by and construed under the laws of the State of Illinois. . To secure the wire into the terminal, insert the exposed wire into the hole on the side of the terminal next to the screw marked common. . . 4 years from the date of installation when purchased and installed by a contractor and when used intermittently as a sump pump, otherwise 3 years The defective product must be returned directly to the factory, postage prepaid with the original bill of sale or receipt to the address listed below. Locate the desired activation point. CONNECTION TO AN EXISTING DISCHARGE PIPE (Diagram B). . The float switch wire of the Enhanced Controller includes a connector that can be separated from the controller when the wire needs to be threaded through small openings. In instances where the discharge line is exposed to freezing temperatures, the pipe must be sloped downward so any remaining water will drain out. . An in-line check valve is recommended to prevent back-flow. The float switch wire can now be disconnected. KEEP OUT OF REACH OF CHILDREN. Wash hands after handling. . This type of battery will power the controller for many hours, but not indefinitely. _mduj` fly kfjculothdl dr gkgregloy, dr tmg FO pdwgr, tmg Qrd _grhgs systgk whjj sdul`, odltrdj ulht whjj hl`hoftg tmg ofusg dc tmg, Cdr f``g` rgjhfnhjhty, tmg cjdft swhtom mfs, ldt, dlg, nut twd cjdfts kdultg` whtmhl f prdtgothvg, prdtgothvg ofeg prgvglts `gnrhs dr dtmgr whrgs. The product must be returned to GLENTRONICS, INC. for inspection in order to be considered for warranty service. . To avoid debris pouring into the float, it should be positioned on the side of the discharge pipe opposite the drain tile. DO protect the electrical cord from sharp objects, hot surfaces, oil and chemicals. In the event of an accident, flush with water and call a physician immediately. 6.Place the pump with the PVC pipe attachment on the bottom of the sump floor next to the main AC pump. As the pump evacuates the water from the pit the float will fall and turn off the pump. . A light on the display panel of the, control unit will indicate the cause of the alarm, A Pro Series 2200 Standby Battery or a Pro, DO NOT use an automotive battery with this, one, but two floats mounted within a protective, cage. any latin characters (a-z, A-Z) any numbers (0-9) special characters ("-", "_" and "."). DO NOT pull the cord when disconnecting the control unit. . If the security system requires a closing of a contact to activate the alarm, secure the other wire into the terminal hole labeled N.O. If the float switch does not move freely the pump will not activate. If the battery is good, the light will go out. Although the deluxe controller can not run the pump, it will sound an alarm indicating the loss of power. . This pump is wired with a 3-prong grounded plug. ALWAYS remove the power cord from the electrical outlet before connecting or disconnecting the battery cables. The dealers dated bill of sale, or installers invoice must be retained as evidence of the date of purchase and to establish warranty eligibility. If you do not agree to the terms of the warranty, do not use the product and return it within the return period stated on your purchase receipt from the retail store or authorized distributor where you purchased it for a refund. If there is a failure with either the main pump or the plumbing system, the water level will rise past the primary float switch and activate the water sensor. To reduce the risk of electrical shock, be, Someone should be within range of your voice or close enough to come to your aid when you work near a. . Make sure it is installed with the arrow pointing up or it will not prevent the backflow of water. When a check valve is used, a 1/8 hole must be drilled in the PVC pipe above the Pro Series pump. 3.When a check valve is used, a 1/8 hole must be drilled in the PVC pipe above the Pro Series pump. . f rhsb dc chrg dr hliury crdk fl gjgotrhofj smdob. To help reduce these risks, observe the following precautions: DO NOT walk on wet areas of the basement until all power has been turned off. After the initial installation, be sure to check the pump operation by filling the sump with water and observing the pump through several full cycles. 2.Secure the pump wire so that the plug on the end will not fall into the sump. DO NOT place the controller on the floor. Secure the pump wire so that the plug on the end will not fall into the sump. When connecting the battery cables, first connect the small ring on the end of the WHITE wire to the NEGATIVE (-) post of the battery, and then connect the large ring on the end of the BLACK wire to the POSITIVE (+) post of the battery. Enter your email address and check your inbox. . To the extent permitted by law, this warranty and the remedies set forth are exclusive and in lieu of all other warranties, remedies and conditions, whether oral, written, statutory,express or implied. The electrical outlet should be within the length of the pumps power cord, and at least 4 feet above the floor level to minimize potential hazards from flood conditions. 4.If there is no check valve on the discharge pipe of the main AC pump, one must be installed at this time. 0% found this document useful, Mark this document as useful, 0% found this document not useful, Mark this document as not useful, Save 278_2_Pro+Series+PHCC-2400+Manual For Later, systgk hlstfjjg` ny sdkgdlg gjsg, ydu kust rgf` fl` cdjjdw tmg. This pin will prevent the float switch from accidently being disconnected from the controller. This pin will prevent the float switch from accidentally being disconnected from the controller. This will preserve the battery and silence the alarm. . The controller should be mounted at least 4 from the floor and 1 from the outlet. . DO NOT use the control unit for charging dry-cell batteries that are most commonly used with home appliances.
Note: It is important to mount the float so that the activation level is below the drain tile that empties into the pit.